NZXT Hale82 850W Power Supply Review

1. Introduction2. NZXT Hale82 850W (Bundle & Cables)3. NZXT Hale82 850W4. NZXT Hale82 850W (Internal)5. NZXT Hale82 850W (Super High Res Gallery)6. Testing Methodology & Results7. Closing Thoughts8. View All Pages

The Hale90 series of power supplies has been a great success for NZXT, targeting the high end enthusiast audience. Today we are looking at a power supply in their new Hale82 range, which targets a wider, cost aware user base. All of the Hale82 power supplies feature 80 Plus Bronze efficiency and a semi modular cabling system.

Features

• 80+ Bronze Certification – The HALE82 series from NZXT operates with high efficiency: at 20%, 50%, and 100% loads, efficiencies are 82%, 85%, and 82% respectively.
• 100% Japanese Capacitors – High quality components promote longer lifespan and better reliability.
• 120mm Two-Ball Bearing Fan – For smooth, silent rotation and optimal air intake.
• Strong Single +12V Rail – A single +12V rail provides stability and ease of use with the ability to deliver clean currents under a heavy load.
• Modular Design – Includes a selection of flat cables that allow the user to pick and choose which cables they want to use, maximizing cable management and airflow inside chassis.
• Large Tower Support – Extended 8pin connector for bottom mounted cases or large cases.
• Dual 8pin connector – For high end motherboards dedicated to overclocking.
• Keeping it Safe – The HALE80 series offers over voltage, current, power, temperature, under voltage, and short circuit protection.

The NZXT Hale82 850W ships in a ‘sporty' looking box, predominately black with yellow stripes on the front.

Inside, the power supply is protected inside a foam protective surround. The modular cables are stored in a white bag at the side.

NZXT supply a region specific power cable, a user manual and some mounting screws for system installation.

The modular cables are shipped in a white pouch, this is reusable for storage later.

Some of the cables are hardwired, as shown in the bottom picture, above.

The 120mm fan immediately catches the eye, due to the contrasting white colour scheme against the black paintwork of the chassis.

The rear of the power supply is fully vented to aid airflow. There is a power button and switch offset to the side.

The NZXT logo is embossed into the side panel, which can only be seen under certain light. The other side panel doesn't have this engraving.

The modular cable connectors are clearly labelled to make the installation procedure as easy as possible. The PCI-E and CPU connectors are 4×4 pin and the peripheral connectors are 3×3 pin.

NZXT Hale82 850W Power Supply
DC Output	+3.3V	+5V	+12V	-12V	+5Vsb
Max Output	25A	25A	70A	0.5A	3A
Total Power	150W		840W	6W	15W
	850W

The Hale82 850W supply can deliver a total of 70A on the +12V output for a total of 840W.

The 120mm fan is an ADDA unit, model ‘AD1212UB-A70GL'. This is a dual ball bearing fan rated 12V, 0.5A.

This is a Seasonic design, one of our favourite manufacturers in the industry now for many years. The internal build is very clean, with several long heatsinks strategically placed to aid with heat dissipation.

The AC receptacle and the on/off switch are connected to a PCB which also contains two Y capacitors, an X capacitor and a CM choke. Nearby there are two bridge rectifiers attached to a heatsink.

The two main primary stage capacitors are Nippon Chemi Con, rated 330uF, 400V to 105c. The minor rails are generated through two DC-DC convertors which are all held on the same PCB.

All of the capacitors on the secondary side are also Nippon Chemi Con and are rated at 105c.

All of the cables are sleeved into the chassis and tied down. NZXT also place a rubber grommet on the chassis for further protection against long term fraying.

On this page we present some super high resolution images of the product taken with the 24.5MP Nikon D3X camera and 24-70mm ED lens. These will take much longer to open due to the dimensions, especially on slower connections. If you use these pictures on another site or publication, please credit Kitguru.net as the owner/source.

Additional technical assistance: Peter McFarland and Jeremy Price.

Correctly testing power supplies is a complex procedure and KitGuru have configured a test bench which can deliver up to a 2,000 watt DC load. Due to public requests we have changed our temperature settings recently – previously we rated with ambient temperatures at 25C, we have increased ambient temperatures by 10c (to 35c) in our environment to greater reflect warmer internal chassis conditions.

We use combinations of the following hardware:
• SunMoon SM-268
• CSI3710A Programmable DC load (+3.3V and +5V outputs)
• CSI3711A Programmable DC load (+12V1, +12V2, +12V3, and +12V4)
• Extech Power Analyzer
• Extech MultiMaster MM570 digital multimeter
• Extech digital sound level meter
• Digital oscilloscope (20M S/s with 12 Bit ADC)
• Variable Autotransformer, 1.4 KVA

12V output is combined for our testing.

DC Output Load Regulation
Combined DC Load	+3.3V		+5V		+12V		+5VSB		-12V
	A	V	A	V	A	V	A	V	A	V
100W	1.52	3.33	1.75	5.04	6.61	12.08	0.50	5.03	0.20	-12.11
225W	3.76	3.32	3.83	5.03	15.51	12.06	1.00	5.02	0.20	-12.10
450W	7.54	3.31	8.34	5.02	30.74	12.04	1.50	5.01	0.30	-12.08
675W	11.30	3.30	12.31	5.01	47.51	12.00	2.00	4.99	0.50	-12.06
850W	1.44	3.29	1.15	5.00	63.33	11.97	0.50	4.99	0.20	-12.05

The NZXT Hale82 850W produces strong load regulation across all output. They all achieved between +/-3% of the nominal voltage instead of the recommended +/-5%.

NZXT Hale82 850W	Maximum Load
	909W

We managed to get the PSU to achieve 909W before it would shut down, delivering around 59W more than the rated specifications.

Next we want to try Cross Loading. This basically means loads which are not balanced. If a PC for instance needs 500W on the +12V outputs but something like 30W via the combined 3.3V and +5V outputs then the voltage regulation can fluctuate badly.

Cross Load Testing	+3.3V		+5V		+12V		-12V		+5VSB
	A	V	A	V	A	V	A	V	A	V
760W	1.0	3.33	1.0	5.02	60.0	11.95	0.2	-12.04	0.50	5.01
165W	15.0	3.28	18.0	5.00	2.0	12.07	0.2	-12.02	0.50	4.99

These are exceptional results under intensive load changes, with all output holding well. The +12V output fluctuates by only 0.12 when loaded.

We then used an oscilloscope to measure AC ripple and noise present on the DC outputs. We set the oscilloscope time base to check for AC ripple at both high and low ends of the spectrum.

ATX12V V2.2 specification for DC output ripple and noise is defined in the ATX 12V power supply design guide.

ATX12V Ver 2.2 Noise/Ripple Tolerance
Output	Ripple (mV p-p)
+3.3V	50
+5V	50
+12V1	120
+12V2	120
-12V	120
+5VSB	50

Obviously when measuring AC noise and ripple on the DC outputs the cleaner (less recorded) means we have a better end result. We measured this AC signal amplitude to see how closely the unit complied with the ATX standard.

AC Ripple (mV p-p)
DC Load	+3.3V	+5V	+12V	5VSB
100W	5	5	15	10
225W	10	10	20	10
450W	10	10	20	10
675W	10	10	25	10
850W	15	10	35	15

Ripple results are extremely impressive across all the rails, the Seasonic design peaking at only 35mW on the 12V+ output at 100% load.

Efficiency (%)
100W	84.35
225W	86.23
450W	88.89
675W	87.74
850W	85.58

For a 80 Plus Bronze specified unit, these results are some of the best we have seen to date, peaking at around 89 percent efficiency at 50 percent load. At 100 percent load, this drops to 85.58 percent, which is a fantastic result.

We take the issue of noise very seriously at KitGuru and this is why we have built a special home brew system as a reference point when we test noise levels of various components. Why do this? Well this means we can eliminate secondary noise pollution in the test room and concentrate on components we are testing. It also brings us slightly closer to industry standards, such as DIN 45635.

Today to test the power supply we have taken it into our acoustics room environment and have set our Digital Sound Level Noise Decibel Meter Style 2 one meter away from the unit. We have no other fans running so we can effectively measure just the noise from the unit itself.

As this can be a little confusing for people, here are various dBa ratings in with real world situations to help describe the various levels.

KitGuru noise guide
10dBA – Normal Breathing/Rustling Leaves
20-25dBA – Whisper
30dBA – High Quality Computer fan
40dBA – A Bubbling Brook, or a Refridgerator
50dBA – Normal Conversation
60dBA – Laughter
70dBA – Vacuum Cleaner or Hairdryer
80dBA – City Traffic or a Garbage Disposal
90dBA – Motorcycle or Lawnmower
100dBA – MP3 Player at maximum output
110dBA – Orchestra
120dBA – Front row rock concert/Jet Engine
130dBA – Threshold of Pain
140dBA – Military Jet takeoff/Gunshot (close range)
160dBA – Instant Perforation of eardrum

Noise (dBA)
100W	29.3
225W	30.7
450W	31.2
675W	33.5
850W	35.8

The power supply is basically inaudible until around 400-450W output when the fan spins up a little, creating a whisper of fan noise. It isn't until around 650W output that the fan is audible, however it doesn't become intrusive. At full load, the fan can be easily heard, although this isn't a practical real world situation.

Temperature (c)
	Intake	Exhaust
100W	36	38
225W	38	43
450W	40	46
675W	43	53
850W	45	57

The fan spins moderately once the supply is loaded to around 450W, maintaining good ambient temperatures right up to full load.

Maximum load	Efficiency
909W	83.8%

For those interested, we measured efficiency when stressing the unit to breaking point. 83.8% at 909W … hardly practical in the real world, but interesting.

The NZXT Hale82 850W Power Supply performed admirably throughout our testing thanks in part to the very capable Seasonic design. We have generally found Seasonic to be one of the best OEM partners in this industry, throughout the years.

The appearance of the power supply might split opinion, although I personally feel the large white coloured fan helps the product to stand out visually in such a crowded market place. Technically, it helps that the fan doesn't emit a lot of noise too, even when loaded within the last 30% of power output. It is only clearly audible in the last 10% of total output.

Internally, the Seasonic design lives up to our expectations, generating very high levels of efficiency, particularly as NZXT have applied for a modest 80 Plus Bronze Certification. Voltage regulation is certainly a key talking point, remaining within a 3 percent variable. Our intensive cross loading tests highlighted a very stable design, with little fluctuation across any of the output.

Ripple suppression is also noteworthy, particularly from the +12V output, which peaked at 35mV when at full load. The use of high grade Nippon Chemi Con 105c rated capacitors throughout will be sure to aid with long term stability, especially in less than perfect thermal conditions.

This market is so crowded that it is difficult to give this product a ‘Must Have' award, however it is certainly worth shortlisting at the top of a list … if overall performance, power regulation and stability are primary prerequisites.

Currently the pricing in the United Kingdom has been confirmed at £119.99 inc vat, with availability soon.

Pros:

• Very stable power regulation.
• Excellent efficiency.
• Low noise.

Cons:

• there are many quality competitors in this market.

Kitguru says: A very capable power supply and definitely worth buying.

Become a Patron!