Corsair TX 850W V2 Power Supply review

1. Introduction2. Corsair TX 850W V2 3. Corsair TX 850W V2 (Internal)4. Testing Methodology and Results5. Closing Thoughts6. View All Pages

KitGuru loved the Corsair AX series of power supplies, their class leading efficiency and attention to detail earned them our highest awards. Today we are looking at an update to their more affordable TX series. The TX V2 range is designed for enthusiasts who need a high quality power supply but who don't need modular cables that can be disconnected from the main unit.

The original TX series won many awards worldwide and Corsair hope that this updated range will be just as successful. The new range includes high specification components such as 105c Japanese capacitors, a quality 140mm fan and solid load regulation.

The new TX V2 power supplies also offer increased energy efficiency, rated 80 Plus Bronze with ErP compliancy. Corsair have also spent time reducing the noise levels when compared directly to the original TX series.

For peace of mind, Corsair are also giving a 5 year warranty with this new range. This latest TX V2 850W power supply delivers a whopping 70 AMP via a single +12 Rail (840w) so it caters for the most demanding graphics cards on the market.

The Corsair TX 850W V2 arrives in a stylish box featured a sepia tinted image of the PSU chassis. Their artwork design is some of the best on the market in our opinion.

The bundle contains a power cable, cable ties, mounting screws and a well written manual.

The Corsair TX 850W V2 is securely protected inside two soft foam inserts and is wrapped in a felt pouch to stop scuffing during shipping.

As this power supply is not a modular design, all cables enter the chassis from the front. They are supplied with a hefty cable tie around them for transportation.

As we had hoped, the power supply is extremely attractive, with nicely designed stickers on the sides and a reassuringly large 140mm fan delivering the cooling. The subtle matt paintwork is excellent and won't mark or chip easily.

Connectivity is very strong and 4 x 6+2 pin PCI-E power connectors will appeal to the hardcore gaming community who want a performance SLI or CrossfireX system.

Model	CMPSU-850TX V2
	AC Input Rating
AC Input	90-264V
Input Current	6-12A
Frequency	47-63hz
	DC Output Rating
	Max Load	Max Output
+3.3V	25A	150W
+5V	25A
+12V	70A	840W
-12V	0.5A	6W
+5VSB	3.0A	15W
Total Power	850W (continuous @ 50c ambient temperature

The unit features a very strong 12V rail delivering up to 70A (840W).

The fan is a Yate Loon D14BH-12 140mm unit which can spin up to 2,800 rpm while pushing 140CFM. The maximum noise is rated by the manufacturer up to 48.5 dBa, but we doubt it will get close to this, even under full load. This is however a seriously high performance fan and a great choice by Corsair.

The overall design of the power supply is very clean with oversized heatsinks helping to ensure that temperatures remain within parameters. The 850W TX V2 is tested and guaranteed to deliver its rated specifications at an ambient temperature of 50c.

High quality Rubycon capacitors are used, rated at 400v 330uF and to 105c. As we would expect there is over current and under voltage protection and the PSU conforms to all required international safety standards. Over current protection (OCP) for example is present on all rails, including the single +12V rail (which can deliver 70 Amps – 840w).

The cabling is sleeved into the chassis to ensure long term safety and protection against fraying.

Additional technical assistance: Peter McFarland and Jeremy Price.

Correctly testing power supplies is a complex procedure and KitGuru have configured a test bench which can deliver up to a 2,000 watt DC load. Over the coming months this configuration is likely to be adjusted further and fine tuned. Ambient room temperatures are kept to a ‘real world’ realistic condition of 23c with air conditioning.

We use combinations of the following hardware:
•  SunMoon SM-268
•  CSI3710A Programmable DC load (+3.3V and +5V outputs)
•  CSI3711A Programmable DC load (+12V1, +12V2, +12V3, and +12V4)
• Extech Power Analyzer
• Extech MultiMaster MM570 digital multimeter
• Extech digital sound level meter
• Digital oscilloscope (20M S/s with 12 Bit ADC)
• Variable Autotransformer, 1.4 KVA

DC Output Load Regulation
Combined DC Load	+3.3V		+5V		+12V		+5VSB		-12V
	A	V	A	V	A	V	A	V	A	V
100W	1.58	3.34	1.77	5.04	6.64	12.12	0.50	5.02	0.20	-12.12
225W	3.70	3.32	3.83	5.03	15.55	12.09	1.00	5.02	0.20	-12.12
450W	7.51	3.31	8.37	5.02	30.68	12.08	1.50	5.01	0.30	-12.13
675W	11.31	3.30	12.39	5.01	47.46	12.05	2.00	5.00	0.50	-12.15
850W	1.31	3.29	1.10	5.00	70.46	12.00	0.50	4.98	0.20	-12.15

The TX850 delivered excellent load regulation on all output channels across a wide range of loads. These are exceptional results and the +3.3V and 5V rails remained firmly within +/-2% of the nominal voltage instead of the recommended +/-5% and the +12V rail held within +/- 1%, even when it was forced to deliver over 70 Amps.

Corsair TX850	Maximum Load
	925W

We managed to get the PSU to hit 925W before it would shut down. delivering around 75W more than the rated specifications. It would run at 920W for quite a while.

Next we want to try Cross Loading. This basically means loads which are not balanced. If a PC for instance needs 500W on the +12V outputs but something like 30W via the combined 3.3V and +5V outputs then the voltage regulation can fluctuate badly.

Cross Load Testing	+3.3V		+5V		+12V		-12V		+5VSB
	A	V	A	V	A	V	A	V	A	V
760W	1.0	3.26	1.0	5.02	65.0	11.97	0.2	-12.07	0.50	5.00
165W	15.0	3.30	18.0	4.97	2.0	11.99	0.2	-12.06	0.50	4.97

Again, these are very good results with fluctuation held safely within the rated parameters, even when loading the unit with 65A on the 12V.

We then used an oscilloscope to measure AC ripple and noise present on the DC outputs. We set the oscilloscope time base to check for AC ripple at both high and low ends of the spectrum.

ATX12V V2.2 specification for DC output ripple and noise is defined in the ATX 12V power supply design guide.

ATX12V Ver 2.2 Noise/Ripple Tolerance
Output	Ripple (mV p-p)
+3.3V	50
+5V	50
+12V1	120
+12V2	120
-12V	120
+5VSB	50

Obviously when measuring AC noise and ripple on the DC outputs the cleaner (less recorded) means we have a better end result. We measured this AC signal amplitude to see how closely the Corsair unit complied with the ATX standard.

AC Ripple (mV p-p)
DC Load	+3.3V	+5V	+12V	5VSB
100W	5	10	20	10
225W	10	15	20	15
450W	10	15	30	15
675W	15	20	40	15
850W	15	20	45	20

Ripple results are very impressive, across the board. The 12V rail registered around 45 mV with our equipment, which is well within the Tolerance guidelines.

Efficiency (%)
100W	86.34
225W	87.34
450W	88.85
675W	87.78
850W	86.03

For a 80 Plus Bronze specified unit, these results are very strong, showing a maximum efficiency rating, just shy of 89%. At maximum load this drops to around 86%, which is again, a great result.

We take the issue of noise very seriously at KitGuru and this is why we have built a special home brew system as a reference point when we test noise levels of various components. Why do this? Well this means we can eliminate secondary noise pollution in the test room and concentrate on components we are testing. It also brings us slightly closer to industry standards, such as DIN 45635.

Today to test the Corsair Power Supply we have taken it into our acoustics room environment and have set our Digital Sound Level Noise Decibel Meter Style 2 one meter away from the unit. We have no other fans running so we can effectively measure just the noise from the unit itself.

As this can be a little confusing for people, here are various dBa ratings in with real world situations to help describe the various levels.

KitGuru noise guide
10dBA – Normal Breathing/Rustling Leaves
20-25dBA – Whisper
30dBA – High Quality Computer fan
40dBA – A Bubbling Brook, or a Refridgerator
50dBA – Normal Conversation
60dBA – Laughter
70dBA – Vacuum Cleaner or Hairdryer
80dBA – City Traffic or a Garbage Disposal
90dBA – Motorcycle or Lawnmower
100dBA – MP3 Player at maximum output
110dBA – Orchestra
120dBA – Front row rock concert/Jet Engine
130dBA – Threshold of Pain
140dBA – Military Jet takeoff/Gunshot (close range)
160dBA – Instant Perforation of eardrum

Noise (dBA)
100W	27.7
225W	28.3
450W	30.7
675W	35.8
850W	40.3

Noise levels are low, with the system only becoming audible in the final 25% of output. Under 500W load it would be hard to know the unit was actually on.

Temperature (c)
	Intake	Exhaust
100W	35	36
225W	36	38
450W	38	44
675W	42	48
850W	44	52

Exhaust temperatures are excellent, rising to a 8c above ambient result at full load. This 140mm fan works hard in the last 15% of output, but temperatures are well maintained. Corsair could have actually relaxed the fan profile a little if they wanted.

Maximum load	Efficiency
925W	84.34%

For those interested, we measured efficiency when stressing the unit to breaking point. Over 84% at 925W … hardly practical, but interesting regardless.

When we reviewed the Corsair AX850W power supply we received a lot of positive feedback from our readers. Almost everyone wanted to buy one, but only a small percentage were willing to part with the £160 required for pride of ownership.

Corsair have released the TX850W V2 to address a larger audience who still want a quality, high output enthusiast grade power supply for their gaming system. Compromises have to be made when compared to the AX unit, so you lose modular cable functionality and efficiency is rated to 80 Plus Bronze, rather than 80 Plus Gold.

In reality, this power supply is still capable of almost 89 percent efficiency at around 50 percent load, which is exceptionally good for a Bronze Certified design. Cross loading is rock solid, temperatures are great, and acoustics performance is tuned for optimum ambient temperatures. We would like a little less noise in the last 25% of the ultimate power range, but Corsair have clearly optimised the fan profile to ensure maximum cooling proficiency.

Corsair are offering this power supply for £60 less than the high end AX model, and Dabs are selling it now for £102 inc vat which will certainly open up sales to a much wider audience. Many people put a limit of £100 inc vat for a quality power supply purchase, so this would be a great first choice, especially if you wanted to build a high performance SLI or CrossfireX gaming system without breaking the bank.

KitGuru says: Performance is solid in all areas and we like the attention to detail. If you can live with a non modular design this is one of the best power supplies we have tested.

Become a Patron!